Plumbing, draining and gasfitting work
In NSW, you need the right licence or certificate to do plumbing, draining, or gasfitting work. Before you apply you must meet the eligibility criteria, which include qualifications and experience.
Key information
- In NSW, you need a licence or certificate to do any plumbing, draining or gasfitting work regardless of the cost of the work or whether the work is residential, commercial or industrial.
- There are several types of licence available depending on the work you need to do.
- You need to be licensed in every category you intend to work in or under either the 'immediate supervision' or 'general supervision' of a person who is appropriately licenced.
- You must have the approved qualifications and experience before you can apply for a licence or certificate.
- You can apply to have a licence or certificate issued for 1, 3 or 5 years.
When you will need a plumbing, draining or gasfitting licence
In NSW, you need a licence or certificate before you can do any plumbing, draining or gasfitting work (including LP gasfitting), regardless of the cost of the work or whether the work is residential, commercial or industrial.
Plumbing, drainage and gasfitting includes many different categories of work. Each category is explained below.
You need to be licensed in every category you intend to work in.
You can apply for licences in different categories either all at once or individually.
If you need to add a new category later, you can do so by submitting a new application.
When does plumbing and gasfitting work need to be supervised?
Any work being done by a person who holds a tradesperson certificate issued by Building Commission NSW must be done under the ‘general supervision’ of a person who holds a contractor licence or qualified supervisor certificate. The work must also be signed off by them.
Any work being done by a person who does not hold any form of a licence (including apprentices) must be under the ‘immediate supervision’ of a person who holds a contractor licence or a qualified supervisor certificate.
Building Commission NSW considers 'immediate supervision' to mean that the supervisor is:
- always physically present and with clear line of sight of the work being carried out by the person they are supervising,
- readily available to provide specific instructions and guidance which is adequate to enable the work to be undertaken correctly by the individual performing it,
- directly overseeing and reviewing the work, and
- ensuring the completed work is compliant and meets all regulatory requirements.
Learn more about supervisor responsibilities.
Applying for a licence or certificate
Licence types you can apply for
Plumbing, draining and gasfitting is specialist work
There are several types of licences available in NSW depending on whether you want to:
- contract to do the work,
- supervise work,
- do the work, or
- do a combination of these roles.
The licence types that apply to plumbing, draining and gasfitting work are:
- Individual contractor licence
- Company or partnership contractor licence
- Qualified supervisor certificate
- Tradesperson certificate or provisional tradesperson certificate.
You can apply for these licence types for 1, 3 or 5 years. However, provisional tradesperson certificates are issued for 3 years and cannot be renewed.
Please note all individual applicants must submit a National Police Check (NPC) no older than 4 months from application.
You can also get started with applying for your licence or certificate at Service NSW.
Time frames for licensing and registration applications
Find out about the current application processing times for different licence and registration categories.
Categories of work
The description for each category of plumbing, draining and gasfitting work can be found in schedule 4 of the Home Building Regulation 2014.
‘Plumbing’ includes water plumbing, sewerage and sanitary work. It does not include draining work or roof plumbing.
- Water plumbing is work carried out in connection with the supply or conveyance of water. It includes the installation, alteration, extension, disconnection, removal, renewal, repair and maintenance of pipes, tanks, fixtures, appliances and fittings designed to convey, store, protect, treat, mix, measure, modify or regulate the flow of water, including hot water.
- Sewerage work is the construction, alteration, extension, disconnection, removal, maintenance, repair, renewal, ventilation, flushing or cleansing of any sewerage service pipes, or fittings or fixtures connecting, or intended to connect, directly or indirectly with a sewer or onsite wastewater management systems.
- Sanitary plumbing is work carried out in connection with the collection, conveyance or disposal of sewage, liquid trade wastes and other permitted discharges. It includes the installation, alteration, extension, disconnection, removal, renewal, repair and maintenance of pipes, tanks, fittings, appliances and fixtures designed to receive, convey, store, treat, modify or regulate the flow of sewage, liquid trade wastes or other permitted discharges. It includes the ventilation of those pipes, tanks, fittings, fixtures and appliances.
Water plumbing is the work of water supply, which is the construction, alteration, extension, disconnection, removal, maintenance, repair, renewal or clearing of any pipes or fittings of any water service connecting (or intending to connect) directly or indirectly with a water main.
This includes work on pipes and fittings, whether they are connected (or intended to be connected to) a water main or not, in a building in which any part of the sewerage service is connected to an onsite wastewater management system.
This is water plumbing involved in a fire service as defined in ‘AS/NZS 3500.0:2003, Plumbing and drainage, including a fire sprinkler system and connection of the system to a water main’.
This is water plumbing involved in a fire sprinkler system installed beyond the sprinkler valve assembly.
The work of irrigation includes the construction, alteration, extension, disconnection, removal, maintenance, repair, renewal or clearing of any pipes, fittings or equipment of any irrigation system communicating (or intending to communicate) directly or indirectly with any water main, and the connection of the system to a water main.
Draining is the work of sanitary drainage. This is the construction, alteration, extension, disconnection, removal, maintenance, repair, renewal, ventilation, flushing or cleansing of any sanitary drain connecting (or intended to connect) directly or indirectly with a sewer. This includes work on a house drain connected to an onsite wastewater management system.
Gasfitting work is defined by the Gas Supply Act 1996.
Gasfitting work means any work involved in:
- the installation, alteration, extension or repair of a gas installation
- the installation, alteration, extension, removal or repair of any flue
- the connection of a gas installation to, or the disconnection of a gas installation from, a gas supply point
- the connection of a gas appliance to, or the disconnection of a gas appliance from, a gas installation (otherwise than where the point of connection is a gas outlet socket)
- the connection of a gas container, gas regulator or gas appliance to, or the disconnection of a gas container, gas regulator or gas appliance from, a gas installation (otherwise than where it is readily designed to be detachable from the installation, either with the use of a tool, mechanical force, or otherwise).
Gasfitting work includes work on a gas installation (other than an autogas installation) connected (or intended to be connected) to a compressed natural gas container.
A gas installation means any pipe or system of pipes (and associated fittings and equipment) used to convey or control gas, which are downstream from the gas supply point. It includes any flue that is downstream from a gas supply point. It does not include anything beyond the gas installation end point. It also does not include an autogas installation.
A gas appliance means any gas burning or gas using appliance that is manufactured, adapted or designed for connection to a gas installation, via a gas outlet socket or otherwise. It includes any liquefied petroleum gas dispenser, catalytic burner or vaporiser. It does not include an internal combustion engine that is installed in or is part of a vehicle, vessel or machine.
LP gasfitting is gasfitting work as defined above but restricted to a gas installation designed to carry liquefied petroleum gas in vapour phase only at pressures not exceeding 150 kilopascals.
Liquefied petroleum gas means a liquid or gaseous substance that is a mixture of hydrocarbons, basically consisting of butane or butene or propane or propene, or any mixture of them.
Advanced LP gasfitting work is gasfitting work as defined above but restricted to liquefied petroleum gas without any restriction as to pressure and whether or not the gas will be conveyed in liquid or vapour phase.
It includes work on pipes, fittings, or appliances attached to or forming part of a liquefied petroleum gas transport container.
Qualifications and experience needed
Individuals applying for a contractor licence, supervisor or tradesperson certificate must satisfy the qualification and experience requirements for the relevant category of work.
If applying for an individual licence or certificate, you must also have a valid National Police Check (NPC) Certificate.
Find out below what the qualifications and experience you need to get a licence or certificate are for:
To find organisations that deliver nationally recognised training, go to the Your Career website and search via the course code or name.
If you are currently an apprentice or trainee, you cannot be issued with a licence or certificate. Once you have completed your apprenticeship or traineeship, you will need to apply for a contractor licence if you intend to do, or contract for, building or trade work.
If you hold a licence from interstate or New Zealand, and want to work in NSW, see Working interstate and mutual recognition.
This category of building and trade work is included under the NSW Automatic Mutual Recognition (AMR) scheme.
If you train overseas, see Overseas trained applicants.
Important: Some listed qualifications and units may no longer be available. You should confirm availability with a registered training organisation (RTO) and check the National Training Register before commencing training or recognition of prior learning (RPL).
Assessing experience
Where we say 'experience' is required, this means experience you have gained as an employee who has been paid in line with an award or enterprise agreement.
You can get the experience during or after completing an apprenticeship or traineeship.
You must get referees to verify your experience using the Referee Statement - Plumbing categories.
Certificate IV in Plumbing and Services (Operations)
If you have not completed an Apprenticeship or Traineeship, your experience can only be counted from the date your Certificate III in Plumbing was issued.
You must provide a copy of your Certificate III in Plumbing.
Any experience gained before your Certificate III in Plumbing was completed will not be accepted.
Other qualifications
If you have not completed an Apprenticeship or Traineeship, your experience can only be counted from the date your qualification was issued.
Any experience gained before your qualification was completed will not be accepted.
Experience gained during your completed apprenticeship or traineeship can be counted.
You must provide evidence that you completed your apprenticeship or traineeship, such as:
- A Certificate of Proficiency (CoP) issued in NSW, or
- An equivalent document for interstate apprenticeships or traineeships.
Not all CoPs are the same. The code on your certificate indicates the type of qualification.
- TCID CoP
Issued to students who complete an apprenticeship in NSW, showing your Training Contract ID (TCID) number. Accepted as proof of completing an apprenticeship. - TSR CoP
Issued through an application for Trade Skills Recognition (not through an apprenticeship). Not accepted where evidence of an apprenticeship is required.
Previous licence or supervisor certificate holders
You do not need to show your qualifications if you have:
- ever held an endorsed contractor licence, qualified supervisor certificate or tradesperson certificate in plumbing, draining and gasfitting that was not subject to restrictions or conditions. In this case:
- if you apply for a new endorsed contractor licence or qualified supervisor certificate, we will accept your previous licence or certificate in place of the current qualification requirements.
- held an endorsed contractor licence, qualified supervisor certificate or tradesperson certificate in the last 5 years in plumbing, draining or gasfitting that was subject to restrictions or conditions. In this case:
- we will assess your application and reissue you a licence or certificate that reflects the scope of work that your licence or certificate covered. This may include some conditions or restrictions.
If your application is approved, you will be issued the same licence or qualified supervisor number you had before.
For a contractor licence or qualified supervisor certificate
Experience requirements
You must:
- Complete an apprenticeship or traineeship and at least two years’ combined industry experience in the work covered by the relevant qualification.
If you have completed an apprenticeship or traineeship, it is recommended that you provide evidence of completion of the apprenticeship or traineeship with your application.
OR
- Have at least two years’ combined industry experience in the work covered by the relevant qualification set out below, and this experience was obtained after completing your Certificate III in Plumbing.
We may require evidence of your employment to confirm any employment periods and to verify that you are able to do or supervise the category of work you apply for.
Qualifications
You must complete the following:
Certificate IV in Plumbing and Services (Operations) (CPC40920 or later)
Experience requirements
You must:
- Complete an apprenticeship or traineeship and at least two years’ combined industry experience in the work covered by the relevant qualification.
If you have completed an apprenticeship or traineeship, it is recommended that you provide evidence of completion of the apprenticeship or traineeship with your application.
OR
- Have at least two years’ combined industry experience in the work covered by the relevant qualification set out below, and this experience was obtained after completing your Certificate III in Plumbing.
We may require evidence of your employment to confirm any employment periods and to verify that you are able to do or supervise the category of work you apply for.
Qualifications
You must complete the following:
Certificate IV in Plumbing and Services (Operations) (CPC40920 or later)
Experience requirements
You must:
- Complete an apprenticeship or traineeship and at least two years’ combined industry experience in the work covered by the relevant qualification.
If you have completed an apprenticeship or traineeship, it is recommended that you provide evidence of completion of the apprenticeship or traineeship with your application.
OR
- Have at least two years’ combined industry experience in the work covered by the relevant qualification, and this experience was obtained after completing your Certificate III in Plumbing.
We may require evidence of your employment to confirm any employment periods and to verify that you are able to do or supervise the category of work you apply for.
Qualifications
You must complete the following:
Certificate IV in Plumbing and Services (Operations) (CPC40920 or later)
Qualifications
You must complete ONE of the following:
Certificate III in Plumbing (CPC32420 or later) and the units of competency below
- Establish legal and risk management requirements of new business ventures;
- Read and interpret plans and specifications;
- Carry out work-based risk control processes;
- Estimate and cost work;
- Access and interpret regulatory requirements for the plumbing and services industry;
- Install portable fire equipment;
- Install distribution and range pipes;
- Fit- off sprinkler heads, controls and ancillary equipment;
- Install control valve assemblies, actuating devices and local alarms;
- Test the integrity of water-based fire protection systems using pressure;
- Test and maintain fire hydrant and hose reel installations;
- Design and size heated and cold water services and systems.
OR
Certificate III in Fire Protection (CPC32820 or later) and the units of competency below
- Establish legal and risk management requirements of new business ventures;
- Read and interpret plans and specifications;
- Carry out work-based risk control processes;
- Estimate and cost work;
- Access and interpret regulatory requirements for the plumbing and services industry;
- Design and size heated and cold water services and systems.
Qualifications
You must complete ONE of the following:
Certificate III in Plumbing (CPC32420 or later) and the units of competency below
- Establish legal and risk management requirements of new business ventures;
- Read and interpret plans and specifications;
- Carry out work-based risk control processes;
- Estimate and cost work;
- Access and interpret regulatory requirements for the plumbing and services industry;
- Install distribution and range pipes;
- Fit off sprinkler heads, controls and ancillary equipment;
- Install control valve assemblies, actuating devices and local alarms;
- Test the integrity of water-based fire protection systems using pressure.
OR
Certificate III in Fire Protection (CPC32820 or later) and the units of competency below
- Establish legal and risk management requirements of new business ventures;
- Read and interpret plans and specifications;
- Carry out work-based risk control processes;
- Estimate and cost work;
- Access and interpret regulatory requirements for the plumbing and services industry.
Experience requirements
You must:
- Complete an apprenticeship or traineeship and at least two years’ combined industry experience in the work covered by the relevant qualification and units of competency.
If you have completed an apprenticeship or traineeship, it is recommended that you provide evidence of completion of the apprenticeship or traineeship with your application.
OR
- Have at least two years’ combined industry experience in the work covered by the relevant qualification and units of competency.
We may require evidence of your employment to confirm any employment periods and to verify that you are able to do or supervise the category of work you apply for.
Qualifications
You must complete ONE of the following:
Certificate III in Plumbing (CPC32420 or later) and the units of competency below
- Establish legal and risk management requirements of new business ventures; and
- Read and interpret plans and specifications;
- Carry out work-based risk control processes;
- Estimate and cost work;
- Access and interpret regulatory requirements for the plumbing and services industry;
- Design domestic urban irrigation systems;
- Set out, install and commission irrigation systems;
- Install and commission domestic irrigation pumps;
OR
Certificate III in Irrigation Technology (AHC32419 or later) and the units of competency below
- Establish legal and risk management requirements of new business ventures;
- Read and interpret plans and specifications;
- Carry out work-based risk control processes;
- Estimate and cost work;
- Access and interpret regulatory requirements for the plumbing and services industry; and
- Install backflow prevention devices.
Experience requirements
You must:
- Complete an apprenticeship or traineeship and at least two years’ combined industry experience in the work covered by the relevant qualification and units of competency.
If you have completed an apprenticeship or traineeship, it is recommended that you provide evidence of completion of the apprenticeship or traineeship with your application.
OR
- Have at least two years’ combined industry experience in the work covered by the relevant qualification and units of competency, and this experience was obtained after completing the relevant qualification.
We may require evidence of your employment to confirm any employment periods and to verify that you are able to do or supervise the category of work you apply for.
Qualifications
You must complete ONE of the following:
Certificate III in Plumbing (CPC32420 or later) and the units of competency below
- Establish legal and risk management requirements of new business ventures;
- Read and interpret plans and specifications;
- Carry out work-based risk control processes;
- Estimate and cost work;
- Access and interpret regulatory requirements for the plumbing and services industry;
- Design and size sanitary drainage systems;
- Design and size stormwater drainage systems.
OR
Certificate II in Drainage (CPC20720 or later) and the units of competency below
- Establish legal and risk management requirements of new business ventures;
- Read and interpret plans and specifications;
- Carry out work-based risk control processes;
- Estimate and cost work;
- Access and interpret regulatory requirements for the plumbing and services industry;
- Design and size sanitary drainage systems;
- Design and size stormwater drainage systems.
Experience requirements
You must:
- Complete an apprenticeship or traineeship and at least two years’ combined industry experience in the work covered by the relevant qualification and units of competency.
If you have completed an apprenticeship or traineeship, it is recommended that you provide evidence of completion of the apprenticeship or traineeship with your application.
OR
- Have at least two years’ combined industry experience in the work covered by the relevant qualification and units of competency, and this experience was obtained after completing the relevant qualification.
We may require evidence of your employment to confirm any employment periods and to verify that you are able to do or supervise the category of work you apply for.
Qualifications
You must complete ONE of the following:
Certificate III in Plumbing (CPC32420 or later) and the units of competency listed below
- Establish legal and risk management requirements of new business ventures;
- Read and interpret plans and specifications;
- Carry out work-based risk control processes;
- Estimate and cost work;
- Access and interpret regulatory requirements for the plumbing and services industry;
- Design and size consumer gas installations.
OR
Certificate III in Gas Fitting (CPC32720 or later) and the units of competency below
- Establish legal and risk management requirements of new business ventures;
- Read and interpret plans and specifications;
- Carry out work-based risk control processes;
- Estimate and cost work;
- Access and interpret regulatory requirements for the plumbing and services industry;
- Design and size consumer gas installations.
Experience requirements
You must:
- Complete an apprenticeship or traineeship and at least two years’ combined industry experience in the work covered by the relevant qualification and units of competency.
If you have completed an apprenticeship or traineeship, it is recommended that you provide evidence of completion of the apprenticeship or traineeship with your application.
OR
- Have at least two years’ combined industry experience in the work covered by the relevant qualification and units of competency set out below, and this experience was obtained after completing the relevant qualification.
We may require evidence of your employment to confirm any employment periods and to verify that you are able to do or supervise the category of work you apply for.
Qualifications
You must complete ONE of the following:
Certificate III in Plumbing (CPC32420 or later) and the units of competency below
- Establish legal and risk management requirements of new business ventures;
- Read and interpret plans and specifications;
- Carry out work-based risk control processes;
- Estimate and cost work;
- Access and interpret regulatory requirements for the plumbing and services industry;
- Install LP gas storage of aggregate capacity exceeding 500 litres and less than 8KL;
- Design and size consumer gas installations.
OR
Certificate III in Gas Fitting (CPC32720 or later) and the units of competency below
- Establish legal and risk management requirements of new business ventures;
- Read and interpret plans and specifications;
- Carry out work-based risk control processes;
- Estimate and cost work;
- Access and interpret regulatory requirements for the plumbing and services industry;
- Install LP gas storage of aggregate capacity exceeding 500 litres and less than 8KL;
- Design and size consumer gas installations.
For a tradesperson certificate
Qualifications
You must complete ONE of the following:
Certificate III in Plumbing (CPC32420 or later)
OR
Certificate III in Plumbing (CPC32413 or earlier) which includes all units of competency of the draining stream and gas services stream
Qualifications
You must complete the following:
Certificate III in Plumbing
Qualifications
You must complete the following:
Certificate III in Plumbing
Qualifications
You must complete ONE of the following:
Certificate III in Plumbing and the units of competency below
- Install portable fire equipment;
- Install distribution and range pipes;
- Fit off sprinkler heads, controls and ancillary equipment;
- Install control valve assemblies, actuating devices and local alarms;
- Test the integrity of water-based fire protection systems using pressure;
- Test and maintain fire hydrant and hose reel installations.
OR
Certificate III in Fire Protection
Qualifications
You must complete ONE of the following:
Certificate III in Plumbing and the units of competency below
- Design domestic urban irrigation systems;
- Set out, install and commission irrigation systems;
- Install and commission domestic irrigation pumps.
OR
Certificate III in Irrigation Technology and the unit of competency below
- Install backflow prevention devices.
OR
Certificate III in Irrigation (no longer offered) and the units of competency below
- Connect irrigation systems from drinking water supply;
- Install irrigation systems;
- Troubleshoot irrigation systems.
OR
Certificate II in Urban Irrigation (no longer offered)
Qualifications
You must complete ONE of the following:
Certificate III in Plumbing (CPC32420 or later)
OR
Certificate III in Plumbing (CPC32413 or earlier) which includes all units of competency of the drainage stream)
OR
Certificate II in Drainage
Qualifications
You must complete ONE of the following:
Certificate III in Plumbing (CPC32420 or later)
OR
Certificate III in Plumbing (CPC32413 or earlier) which includes all units of competency of the gas services stream
OR
Certificate III in Gasfitting
Transitional arrangement – qualifications completed before 1 November 2024
If you completed an applicable qualification and the relevant units of competency immediately before 1 November 2024 and you apply for a new licence or certificate, we will accept the applicable qualification and the relevant units of competency in place of the current qualification requirements.
You must have completed the applicable qualification and the relevant units of competency in full.
We will not accept applications that have a mix of both transitional arrangement and current qualification requirements.
If you can't give us a certificate or final academic transcript (including course numbers) to prove you finished an applicable qualification and the relevant units of competency before 1 November 2024, you will need to meet the current qualification requirements.
Contact a Registered Training Organisation or TAFE NSW to find the relevant qualifications, including recognition of any prior learning.
To see the list of transitional arrangements refer to pages 8-12 of the 'Qualifications and Experience requirements for an endorsed contractor licence, supervisor or tradesperson certificate for plumbing, gasfitting and related specialist work' Order.
What would you like to do now?
Get in touch with Building Commission NSW
Need help with an application or want to know more about training and accreditation? Get in touch with Building Commission NSW.